What Is Prodigy P2 Used For?


The Prodigy P2 electric brake controller supplies power to your tow vehicle’s brakes proportionally. This means that your trailer brakes at the same time and with the same strength as your vehicle – even in reverse gear. If you have to slam on your truck’s brakes, the trailer’s brakes respond instantly, too – there’s no delay.

The Prodigy are an English electronic dance music band from Braintree, Essex, formed in 1990 by keyboardist and songwriter Liam Howlett. The line-up of the band has included MC and vocalist Maxim, dancer and vocalist Keith Flint, dancer and live keyboardist Leeroy Thornhill, and dancer an…

How do I turn off P2 prodigy?

To remove the Tekonsha Prodigy P2 # 90885 you simply need to detach the harness at the rear of the brake controller. Once that is removed you can tuck the harness up under your dash with some zip ties andthe uninstall the bracket that holds the brake controller as well.

How do you set a P2 prodigy? (video)

https://www.youtube.com/watch?v=wJOOYy9D27Q

How do you use the brake controller in Prodigy 2? (video)

https://www.youtube.com/watch?v=l_IBfj6r8R8

What is NC on Prodigy brake controller?

The nc code on the Tekonsha Prodigy brake controller indicates that no trailer is connected. When you step on the brake pedal though it should still say that the trailer is not connected. It is possible that there is a short being caused by a dirty or corroded connector.

What does C mean on Prodigy brake controller?

The “C” on your Prodigy brake controller like # 90885 means that you have a trailer connected. Your brake controller is simply recognizing there is a draw on the brake output and your brakes should work well.

What does sh mean on a Prodigy brake controller?

Expert Reply: The SH code on the Prodigy Brake Controller, # 90885, indicates that while idle, the brake controller is sensing a short in the brake wire. Tekonsha states that some test lights or non-Tekonsha testers can cause this problem.

What is the difference between P2 and P3 brake controller?

Which is Better the P3 or P2 Prodigy Brake Controller The P3 brake controller part #90195 is functionally the same brake controller as the P2 part #90885 but comes with more features and a better display screen setup.

Can I remove trailer brake controller?

Expert Reply: Yes, you will be able to uninstall your older brake controller and install the Tekonsha P2, # 90885, in its place without the need of any extra steps or parts.

Do electric brakes work in reverse?

Yes, electric brake assemblies will work in reverse. The brake controller in your tow vehicle would still activate in reverse as long as the brakes are applied. The actuating arm of the Dexter assemblies part # 23-27 will apply the brakes when pushed in either direction.

How do you test a prodigy brake controller?

Make sure you have power entering the brake controller on the black wire. On the red wire you will only want power when the brake pedal is pressed. If there is power on the red wire before the brake pedal is pressed you have connected the red wire from the brake controller to the wrong circuit.

What does .C mean on a Primus brake controller?

asked by: Carol F. Expert Reply: With the Primus IQ part # TK90160 the 0.0 means the controller isn’t doing any braking and “. c.” means you have the boost feature engaged. This means you have the braking power set to 0 and have the boost turned on.

What does 5h mean on trailer brakes?

The code 5. H (flashes 2x per second or a steady display) on the Prodigy P2 # 90885 indicates the brake wire is seeing a short during idling conditions.

How do you adjust a prodigy electric brake controller?

Roll the adjustment wheel on the left up or forward (towards the front of the vehicle) to get it to 6. Then you will drive about 20 miles per hour nd fully apply the manual override lever at the bottom (do not use the brake pedal). If the brakes lock up adjust the power down by turning the wheel the other way.

What is a wireless brake controller?

A wireless brake controller is a brake controller that doesn’t require a traditional wiring connection to the vehicle for operation. The Echo® wireless brake controller plugs in between the vehicle-trailer 7-way, eliminating the need for a separate splice-in or factory wiring installation.

What does NC mean on a trailer brake?

Brake Controller Showing NC when Trailer is Hooked Up and Manual Control is Pressed There are 4 potential problems that are stated in the instructions (linked below) that could cause the NC (no connection) reading on your Prodigy P2, part #90885.

How do I know if my brake controller is bad?

Use a circuit tester, and check the red wire that exits the rear of the controller. This wire should only go hot when the brake pedal is pressed. If this checks out ok, then the controller is bad and must be replaced.

How do you troubleshoot a tekonsha brake controller?

  • Check that the front of the controller is level side to side and back to front.
  • Connect the trailer electrical connection plug to the tow vehicle and start the tow vehicle.
  • Check the display reading.
  • Check the display reading.
  • Check the display reading.
  • How do you use a tekonsha trailer brake controller?

  • Hook the trailer to the vehicle’s hitch.
  • Turn the power knob, located on the right side of the Tekonsha Voyager brake controller, to the 12 o’clock position.
  • Accelerate to 25 MPH and apply the trailer brakes using only the manual slide to test the new settings.
  • How do you wire a tekonsha Voyager brake controller? (video)

    https://www.youtube.com/watch?v=MCqUrOLmgh0

    How do you reprogram a trailer brake control module?

  • Step 1: Plug in the trailer wiring harness.
  • Step 2: Allow the brake controller to calibrate.
  • Step 3: Select personal settings.
  • Step 4: Set the maximum output.
  • Step 5: Adjust the sensitivity level.
  • Step 6: Manually activate brakes as needed.
  • How do I disconnect my brake controller? (video)

    https://www.youtube.com/watch?v=YhKY-9pfnqM

    Where is the trailer brake controller located?

    Find a suitable mounting location for the brake controller. On most vehicles, particularly large trucks and SUVs, the best place tends to be below and off to the side of the steering wheel. Here the controller will be easily visible but out of the way. It can also be mounted above the dash.

    Why do my electric trailer brakes lock up?

    The causes of electric trailer brakes locking up are few: 1) Brake controller adjusted incorrectly for the load; 2) Brake controller failure; 3) Grease on the brake shoes; 4) Poorly adjusted brake shoes; 5) Broken brake shoe. When brakes lock up due to controller issues. it is generally both wheels that lock up.

    Do electric trailer brakes need adjusting?

    Note, it is recommended that you check and adjust your trailer brakes every 3,000 miles or 3 months.

    What should I set my trailer brake gain to? (video)

    https://www.youtube.com/watch?v=cDWI7gaqD5Q

    How do you adjust the Primus on a brake controller?

    Start by adjusting the power output to the midpoint on the controller and make sure the boost is off.. Tow the trailer at about 20 miles per hour and then fully apply the manual override. If the trailer brakes lock up then adjust the power down. If they do not lock up adjust the power higher.

    How do you wire a Primus brake controller? (video)

    https://www.youtube.com/watch?v=Sda3k2osgOE

    What is Primus proportional braking system?

    The Primus IQ was created to work with electric over hydraulic braking systems, works proportionally in reverse to make backing into tough spots a bit easier, and – like the Prodigy P3, Prodigy P2, and many other Tekonsha brake controllers – utilizes primary sensor technology to ensure the smoothest stop possible.

    How do you reset a prodigy brake controller?

    The first step that we will want to take is to reset the brake controller. This is done by simply unplugging the brake controller for approximately 20 seconds and then reconnecting the brake controller.


    Leave a Reply

    Your email address will not be published.